 | Crown IQ3USP3CN Expansion Card |
| Crown IQ3USP3CN Expansion Card |
|
Crown IQ3USP3CN Expansion CardCrown IQ3USP3CN The PIP USP3CN module includes all of the features of the PIP USP3 as well as integrating CobraNet transport in the same single 100 MB Ethernet connection. Signal routing is easily controlled via FREE IQWic software. The PIP USP3CN also provides two analog audio inputs that can be configured as a redundant signal or for page over applications. Saves audio bandwidth within the CobraNet network by providing local signal processing of the signal at the amplifier. Also features amplifier output listen bus that allows you to route the amplifier output signal back through Ethernet to a central listening position. Crown IQ3USP3CN Features 100Mb Ethernet single plug solution for both CobraNet audio and TCPIQ control and monitoring Analog audio inputs allow CobraNet network audio input, CobraNet audio backup, or a hardwire emergency override of CobraNet audio Listen Bus amplifier output monitor via CobraNet 24 bit digital to analog conversion with 32 bit, floating point DSP processing 64 assignable filters with 9 different filter types including all pass filters Over 2 seconds of delay available per channel Input compressors and output limiters for each channel Dual, uncorrelated noise generators for noise masking Sine generator Load supervision Full error reporting Firmware upgrades via the network 10 user selectable presets Reliable FLASH memory backup of all parameters Three Year, No Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications Crown IQ3USP3CN Specifications Balanced Audio Input Connector Single 5 pin removable barrier strip connector for both channels AUX Connector Configurable for AUX input or AUX output. Listen Bus is available through CobraNet Communications 100Mb Fast Ethernet conforming to IEEE 802.3 Power Requirements provided by the amplifier 24VDC 350mA, 24VDC 30mA. DSP Processing 32 bit, Floating Point, 665 s latency DAC Conversion 24 bit, 135 s latency Dynamic Range 103 dB typical A weighted, 20Hz 20kHz, audio sourced from muted CobraNet channel Distortion < 0.05 THDN, 20Hz 20kHz Frequency Response 0.5 dB, 20Hz 20kHz InputOutput Monitor Accuracy Typically 1dB Input Impedance Nominally 20 k ohms balanced, 10 k ohms unbalanced Maximum Input Level 20 dBu ADC Conversion 18 bit, 312 s latency Signal to noise ratio 70 dB typical Aweighted, 20Hz 20kHz Crosstalk > 60 dB Common Mode Rejection CMR 50 dB typical Distortion > 0.05 THDN, 20Hz 20kHz Frequency Response 0.5 dB, 20Hz 20kHz Get your Crown IQ3USP3CN today! Close...
|
| Product Name |
|---|
| Crown IQ3USP3CN Expansion Card |
 |
Crown IQ3PIPLITE Expansion CardCrown IQ3PIPLITE Crown IQ3PIPLITE Q PIP Lite Integrates Ethernet based IQ Network™ control via 100 Mb TCPIQ protocol for digital control of analog devices. Since audio signals are not converted to digital, a larger dynamic range is possible. Digital signal control allows for |
$528.00 | ||
 |
Crown IQ3USP3 Expansion CardCrown IQ3USP3 Crown IQ3USP3 IQ PIP USP3 is a DSP based IQ PIPT module that integrates into a 100 Mb Ethernet network via TCPIQ® protocol. An extremely versatile speaker processing unit that mounts right in your Crown amplifier, this compact module greatly reduces the costs of |
$911.00 | ||
 |
Crown TP170V Expansion CardCrown TP170V The Crown® TP 170V is a rack mountable panel with autoformers to provide impedance matching between amplifier outputs and constant voltage loudspeakers. This unit allows amplifiers without direct 70V or 100V output capability to drive distributed speaker systems designed |
$450.00 | ||
 |
Crown MCVCA8 Expansion CardCrown MCVCA8 Crown VCAMC8 Level Control Module The Crown VCA MC4 and VCA MC8 are optional level control modules for the Crown CTs multichannel power amplifiers. The VCA MC4 is for the CTs 4200, and the VCA MC8 is for the CTs 8200. A VCA MC module provides independent remote level |
$241.00 | ||
 |
Crown PIPCLP Expansion CardCrown PIPCLP P.I.P. CLP Clip Elimination Module. P.I.P. CLP is designed to detect and prevent overload. The same error detecting circuit that is used to signal the IOC indicator is used to activate this error driven compressor. It is not a typical signal driven compressor, but a circuit |
$216.00 |
